Home›Fault Codes›Whirlpool Washer LD
🌀
Whirlpool Washer · Error Code
CODE LD · also shows Ld

Whirlpool LDLong drain — water not draining fast enough

A Whirlpool LD means "long drain" — the water isn't leaving fast enough. It's a drain-path problem, not a dead machine. Clean the drain pump filter, check the drain hose for a kink or a too-deep push into the standpipe, then suspect the drain pump. Most LD codes clear with a free filter/hose clean.

🔧 From our repair bench: LD is a drain-speed code — clear the pump filter and make sure the drain hose isn't shoved 12 inches down the standpipe (it siphons and re-triggers).

🐜 Straight talk: this points you at the likely cause — it's not a guarantee, and every machine is different. Cut the power (and shut off gas or water) before you touch anything, test to confirm the part is actually bad before you buy, and if it's beyond you, get a pro. No shame in that.

What the code means

LD: Long drain — water not draining fast enough

Long drain — water not draining fast enough.
Most likely causes
  • Clogged Drain Pump/Filter
  • Kinked Drain Hose
  • Drain Pump Failure
The 2-minute test → Check pump filter for debris; verify pump runs + ohms within spec.
The kit

The Tools to Test + Fix With

You don't need a shop full of tools — you need these. The multimeter is the one that pays for itself the first time it stops you buying the wrong part on a fault code.

Digital multimeter

Test a suspect part for continuity BEFORE you buy — the single best way to avoid replacing the wrong thing on a fault code.

🔎 On Amazon →

Nut driver set (¼" + 5⁄16")

Most appliance panels are held on with ¼" and 5⁄16" hex screws.

🔎 On Amazon →

Screwdriver set (Phillips/flat/Torx)

Covers the odd panel screw and the Torx fasteners many brands use.

🔎 On Amazon →
Fix it — two honest options

The Fix — Free Checks First, Then the Part

Work top-down: the free checks before you spend a dime, and test to confirm the part is actually bad before you buy. When it is a part, you get both options — the genuine OEM part sourced through us and shipped to your door, or a budget aftermarket part on Amazon. Your call.

Free fixFree

No part — clean filter & check hose

Clean the drain-pump filter/coin trap and make sure the drain hose isn't kinked or pushed more than a few inches into the standpipe.

✅ No part needed — try this first
Moderate DIY$25–70

Drain pump

If the filter and hose are clear but the pump hums or is silent on drain. Match your model.

🔧 Genuine OEM — through us → 🔎 Budget on Amazon →

Prices shown are typical aftermarket ranges and vary by brand and model — genuine OEM is priced by quote when you request it. Amazon links open a search so you can match your exact model number; as an Amazon Associate, Appliance Ant may earn from qualifying purchases at no extra cost to you. Always confirm the part fits your model.

Can you fix it yourself?

Safe to Try · Know the Risk · Call a Pro

General guidance, not professional advice. Always unplug the appliance (or shut off the gas/water) before you check anything. If it feels beyond you, that's exactly when to get a pro.

✅ Safe to try yourself

  • Clean the drain-pump filter/coin trap (towel down).
  • Check the drain hose for kinks and how far it goes into the standpipe.
  • Run a drain/spin-only cycle to confirm.

⚠️ Doable — know the risk

  • Drain pump replacement — moderate; power off, water off.

🛑 Call a pro — don't touch this

  • Water reaching the motor/control board.
Is it worth fixing?

The Honest Call

Very worth it — free to clean, $25–70 for a pump. Draining fixes are the cheapest washer repairs there are.

In Middle Tennessee or Louisiana?

Don't want to DIY it? Our own family of technicians will come clear that LD for you — honest flat pricing, usually same-day, 4.5★ from 1,000+ neighbors.

🔧 Get it fixed by our techs →
We come to:Walker, LABaton Rouge, LAHammond, LANew Orleans, LANashville, TNMurfreesboro, TNClarksville, TNFranklin, TN
FAQ

People Also Ask

What does LD mean on a Whirlpool washer?
Long drain — the washer isn't draining fast enough. Usually a clogged pump filter or a kinked/siphoning drain hose; sometimes a failed drain pump.
How do I fix a Whirlpool LD code?
Clean the drain-pump filter and check the drain hose for kinks and how deep it sits in the standpipe. If those are clear and it still drains slowly, replace the drain pump.
Related codes

Other Codes & Fixes

Whirlpool Washer F5E2Washer Not DrainingLG Washer OE